Product Name: 1-Cyanopropyl-1-Methylpyrrolidinium Chloride
Chemical Formula: C9H17ClN2
Synonyms: N-Methyl-N-(3-cyanopropyl)pyrrolidinium chloride
Recommended Use: Commonly handled in chemical synthesis, research settings, potential use in ionic liquid technologies
Manufacturer: Check packaging for full supplier details
Emergency Contact: Refer to local, regional, and national emergency lines for hazardous chemical spills or exposure incidents
CAS Number: 1046398-11-3
UN Number: Not classified under UN numbers for transport
Hazard Classification: Irritant for eyes and skin, possible respiratory sensitizer, harmful if swallowed
Pictogram: Corrosive, Exclamation mark (GHS labels recommended)
Signal Word: Warning
Hazard Statements: Causes severe irritation to eyes, skin, and mucous membranes. Inhalation may result in respiratory tract irritation. If ingested, may produce symptoms like nausea and abdominal pain. Prolonged or repeated exposure may aggravate existing health concerns.
Precautionary Statements: Avoid inhalation, skin, and eye contact. Wear appropriate personal protective equipment. Handle with proper ventilation. Wash thoroughly after handling.
Routes of Exposure: Inhalation, skin absorption, ingestion, eye contact
Target Organs: Respiratory system, skin, eyes
Chemical Name: 1-Cyanopropyl-1-Methylpyrrolidinium Chloride
CAS Number: 1046398-11-3
Concentration: ≥98% (assumed based on laboratory/reagent grades)
Impurities: Potential traces of unreacted starting materials or synthesis by-products (check supplier certificate for specifics)
Molecular Weight: 188.70 g/mol
Inhalation: Remove to fresh air, keep victim calm and warm, seek medical attention if breathing becomes difficult or symptoms persist.
Skin Contact: Remove contaminated clothing, wash affected areas thoroughly with soap and water, seek medical advice if rash or irritation develops.
Eye Contact: Rinse immediately with plenty of water for at least 15 minutes lifting upper and lower eyelids, seek prompt medical evaluation.
Ingestion: Rinse mouth, do not induce vomiting, seek immediate medical help.
Notes for Physicians: Treat symptomatically; chemical irritant exposure protocol applies.
Suitable Extinguishing Media: Dry chemical, CO2, alcohol-resistant foam, or water spray (avoid direct water stream)
Specific Hazards: May emit fumes of hydrogen chloride, nitrogen oxides, cyanide compounds under fire conditions
Special Firefighting Procedures: Use full protective gear and self-contained breathing apparatus
Explosion Hazards: This substance does not form explosive dust-air mixtures under normal handling, but thermal decomposition can generate hazardous gases
Advice for Firefighters: Remain upwind, evacuate personnel from area, isolate hazard zone
Personal Precautions: Wear appropriate PPE including gloves, splash goggles, and lab coat, ensure adequate ventilation, evacuate unnecessary personnel from area
Environmental Precautions: Avoid release into drains, soil, or water bodies to prevent contamination
Methods for Cleanup: Absorb spills with inert material (dry sand, vermiculite), collect in a suitable, labeled container for disposal; ventilate area and wash spill site after material removal
Precautions for Safe Handling: Handle in chemical fume hood or well-ventilated space, avoid contact with skin, eyes, and clothing, keep containers tightly closed
Conditions for Safe Storage: Store in tightly sealed container, protect from moisture and direct sunlight, keep away from incompatible materials such as strong oxidizers
Incompatible Materials: Strong acids, strong bases, oxidizing agents
Hygiene Practices: Wash hands before breaks and after handling, remove contaminated clothing before entering eating areas
Engineering Controls: Use under fume hood or provide local exhaust ventilation
Personal Protective Equipment: Chemical resistant gloves (nitrile recommended), safety goggles, face shield, lab coat
Respiratory Protection: Approved respirator recommended if dust or aerosols are generated and adequate ventilation is not assured
Hand Protection: Impermeable gloves, frequent glove changes
Eye Protection: Chemical splash goggles or face shield
Environmental Exposure Controls: Prevent chemical from entering drains, waterways
Appearance: White to off-white crystalline solid
Odor: Mild, not distinctive
Melting Point: Typically ranges from 120–140°C (literature values may vary)
Boiling Point: Not available (decomposes upon heating)
Solubility: Readily soluble in water and some polar organic solvents
pH: Not determined in solid form
Density: Around 1.2 g/cm³ (estimated by component structures)
Vapor Pressure: Negligible at room temperature
Partition Coefficient (log Kow): Not available
Flash Point: Not flammable under normal temperature (<100°C)
Chemical Stability: Stable under ambient temperatures and prescribed storage conditions
Reactivity: No specific reactivity hazards under recommended use
Conditions to Avoid: Excessive heat, moisture, exposure to strong acids or bases
Hazardous Decomposition Products: Hydrogen chloride, nitrogen oxides, possible cyanide gases when heated to decomposition
Polymerization: Will not polymerize under normal processing
Acute Toxicity: Data on exact LD50 in animals or humans not well established for this specific compound
Routes of Exposure: Inhalation, skin absorption, eye contact, ingestion
Symptoms: Skin and eye irritation, cough, nausea, abdominal discomfort on ingestion or inhalation
Chronic Toxicity: Repeated contact may cause dermatitis or other sensitization reactions
Mutagenicity: Not adequately studied
Carcinogenicity: No classification data available
Aquatic Toxicity: Data not established for this compound; avoid discharge into waterways
Persistence and Degradability: Likely to be persistent due to ionic nature but no specific degradation rates available
Bioaccumulative Potential: No data on bioaccumulation
Mobility in Soil: Likely mobile in aqueous environments given water solubility
Other Effects: Prevent entry into soil, sewers, water systems without pre-treatment
Disposal Methods: Incinerate contaminated waste in an approved chemical incinerator, comply with local, regional, and national hazardous waste regulations
Contaminated Packaging: Dispose of as hazardous chemical waste, rinse thoroughly before recycling or disposing
Environmental Considerations: Avoid release to the environment, check regulations for disposal requirements specific to the location
UN Number: Not regulated for transport as per current international guidelines
Transport Hazard Class: Not classified
Packing Group: Not specified
Proper Shipping Name: Not assigned
Special Precautions: Ship in sealed, clearly labeled containers, prevent spillage during transport
Environmental Hazards: Not considered a marine pollutant under standard criteria but best managed as potentially hazardous
OSHA Status: Not specifically regulated by OSHA
TSCA Status: Check if included in the Toxic Substances Control Act inventory
REACH Status: Evaluate eligibility and pre-registration under REACH regulations if imported or manufactured in significant quantities
SARA Section 313: Not listed on U.S. SARA Title III Section 313 liability list
Canadian DSL/NDSL: Verify listing status with supplier
Hazard Codes (GHS): Eye irritant, skin irritant
Other Applicable Regulations: Review local, regional, national chemical safety guidelines prior to working with or disposing of the material
